Your car’s seat belts are very important and keep all occupants of the car safe. Occasionally, though, they may be congested or trapped. In some cases, this can be a very serious problem that needs to be resolved by the seller. However, you can solve this problem yourself quickly and easily.
You do not need PSAs to remind you how important seat belts are for your safety. After all, it is their responsibility to keep you in your seat and to prevent serious injuries in case you are in danger.
However, seat belts may occasionally be fastened. More than just trouble, a useless seat belt can put you at risk – and who wants that? That’s why you need to know how to fix the problem of seat belt stuck in door.
While it is really possible to take your car to a repair shop and have your seat belt strapped there, you can take care of yourself. Here’s how.
Table of Contents
How Do I Release An Auto-Locked Seat Belt?
Sometimes automatic locking on seat belts may cause them to stick. The problem of automatic locking is simple, with an equally simple solution. All you have to do is loosen the seat belt in this position.
To do this, first, make sure that the seat belt is not fastened and can move freely. Then pull it a little harder to hold more belt. Instead of tying it, let it return to the retractor.
Note the length of the belt and how it hangs. If it returns to normal, then your seat belt stuck in door is solved. However, if you find that it did not pull the whole way and it hangs freely, you may have a much bigger problem. If so, you need to proceed to the next step in this guide.
How To Fix A Seat Belt Stuck In Door?
The actual seat belt machine is a sophisticated device that allows the belt to move because of a rotating gear wheel. The tire may get stuck, which can lead to problems with pulling or pulling the seat belt. Dealing with the machine itself takes more work, but it is still quite possible.
1. Clear The Side Panel First
Since the seat belt path is under the side panel, you need to clear the path to it. For most cars, there should be two separate clips holding it down. These are located near the lower edge of the vehicle. One is on the right, and the other is on the left of column B (center).
You can lift these clips by inserting a flat-headed screwdriver or pliers under the clip and pulling it upwards.
Note that the front clip is a big challenge to unlock because it is attached to the entire car with a hidden screw.
Now, look at the small locked area on the floor of your car, near the center pillar – the one with the button you press to open the trunk.
Use your scraper to open the lid and lock it. This should reveal a small screw. Remove it with your screwdriver. You can now safely delete the previous clip.
2. The Side Panel Must Be Removed
As the clips are gone, removing the side panel should be easy enough.
Get in the back seat of the car. If the side panel (the inner part of the B-axis of your car) appears to be firmly attached to the car, use a flat screwdriver to separate it. If not, you can just pull it out with your hands. At this point, the side panel should not give you any problems, as there are no screws attached to the car.
3. Remove The Seat Belt Mechanism
The way the seat belt reverses is securely fastened with bolts. You need keys of the right size to release them. In most cases, these are 10mm and 14mm.
There is also a clip that connects to the machine, so be sure to remove that. You can use your fingers on this.
Now the seat belt system can be removed from the B-pillar.
There is also a clip that connects to the machine, so be sure to remove that. You can use your fingers on this.
Now the seat belt system can be removed from the B-pillar.
4. Disconnect The Mechanism
Open the device on its side to look at the plastic cap. A few small anchors secure it to the ground. You can remove them using any method you like. For example, you can exit with a hex key.
When you turn the machine to the other side, you should see a small box with its own small pieces. Use a flat object to free them.
Once the pins are out, and the box is loose, you can remove the plastic lid.
5. The Smaller Plastic Pisces Must Be Removed
Under the big cover, you should see two more small pieces of plastic. Rest on the gear, so you need to remove them.
At the top of the second episode, there should also be spring. Take that out again.
6. Change The Gear
Now that you have reached the gear wheel, use your fingers to rotate it clockwise. This article will help you.
Pull the belt to see if the gear shifts freely. If all goes well, you just need to reassemble the machine by restoring your steps.
7. Restore The Mechanism
Re-attach the small pieces of plastic and spring. Then cover them with a large plastic lid. Secure the small box with clips and return the pins inside.
Replace the seat belt strap and attach bolts to the top and bottom. Cut the small device and put it back in the middle. Then return all the panels to where you took them.
You can also find a visual guide to the full process of adjusting the gear belt for the seat belt stuck below.
Conclusion
As you can see, there are many causes behind a seat belt stuck in door. If you are lucky, all you have to do is fix the automatic lock by carefully pulling, or perhaps by giving your seat belt an easy wash.
At times, you may be required to set aside time and effort to correct the matter. But with a little patience – and with the right tools – anyone can fix a strapped seat belt.